Tuesday, September 3, 2013

All rings pattern for 1 shuttle

I needed to make a test of a new thread a got and from one shuttle some more thread remained. I gave it some good use: testing the thread, tatting with beads and inserting pearls in another way I found in one of the books of Irina's Astratenko.

This is the result:


You cannot see in the image, but the thread is a 40 variegated Brildor... strand of 3. 

It is only rings, so you will use 1 shuttle. 
String 1 yellow, 1 red, 1 yellow (this will be used at the last ring) and then 6 times this sequence of seed beads: 1 yellow, 1 red, 1 yellow, 1 white.
Remember: you have to keep in mind that you have to string the beads in reverse order, so you will use first the last bead you strung. Hope it makes sense. This is important only when you have more than 1 color or different sizes. 

So... You start the ring with the first white seed bead in the llop: 4 - 8 - bp 4 - 8. Do not turn work.
Take the next 3 seed beads, hold them firmily between your thumb and index. Take the next white seed bead, make the loop and start the next ring: 4 + 8 bp  4 - 8. 
And so on, until you will have all six rings. 

The rings will tend to curve. If you use only 2 seed beads between the rings, it will curve more, if you use 4 you will have a a nice beaded curved chain inside the bow. Just an idea... I intend to make a complete round but in green with red and white seed beads, it might give a nice wreath.  

Now you turn the work and attack the big ring. 

There is now a trick! You might need a very fine crochet hook or dental floss folded in 2. 
Bring the last 3 seed beads and make the loop for the last ring. 
Work the first half of the ring. Take the dental floss, take the loop thread like if you want to string a bead. Get this floss from underneath of the work between the first ring and the first seed bead, bring enough thread on the upper side of the lace. Now you can string the bigger pearls (mine are 3 mm each) and secure them with a paperclip. And then finish the ring 15ds  bp (with the last 3 seed beads) 15 ds. Close the ring. And then bring the paperclip at the base of the ring and make lock join. 

This diagramm could help a bit: 


Finally, you have to get something like this: 

If you will work with a thicker thread as mine, you should adjust the amound of ds... My piece is really tiny: 2 cm long and 1,5 cm wide... 

Should not be that complicated. 
The last lock join... Make sure you close the last ring completelly  and evenly... Being a big ring, you could consider closing it little by little, sliding gently the first double stiches to the starting point, holding them in place between the lest thumb and indes and pulling the shuttle thread as often as you need. Like this, the ds are more even, at least this method does the job for me. It takes a while to close a ring, but the result pays off. 
Have fun!

6 comments:

  1. Replies
    1. Mariangela, thank you. And if you decide to do it, please let me know if you have some problems in working it or following the pattern.

      Delete
  2. Ton schéma est clair Corina.
    Je vais devoir adapter un peu car perso je n'ai pas de fil 40 ni de perles rondes de 3 mm. Les plus petites que j'ai sont des 4mm et pour le fil du 20 ou 50 donc pour le nb de ds...
    Je vais essayer de le faire cette semaine encore.
    Merci pour le partage et les explications.

    ReplyDelete
  3. Tu peux garder les nd poux les anneaux et je crois aussi les rocailles entre les anneaux peuvent rester les mêmes.
    Pour tes perles, tu fais la première partie de l'anneau plus ou moins pour la longueur des deux perles (quand il est serré), tu retiens le nombre de nd et ça y est.

    ReplyDelete
  4. you're a tatting goddess
    mrsfarid saleh

    ReplyDelete
  5. Lindo! Poderá ser feito com agulha? Obrigada
    Esmeralda

    ReplyDelete